Journal

48 V lithium rack batteries for telecom sites and server rooms: replacing lead-acid

Telecom shelters, base stations and many server rooms run on 48 V DC, traditionally backed by strings of lead-acid batteries whose life shortens in hot shelters. Lithium iron phosphate (LFP) rack modules are a common replacement. Here is what to check so that a module from a Chinese factory works with your rectifiers, survives your site and gets through shipping.

Illustration: a 19-inch rack with 48 V battery modules next to a telecom tower
The module has to match the rectifier, the site and the shipping rules — not only the capacity.

Why sites switch to LFP

LFP modules are smaller and lighter than lead-acid for the same usable energy, tolerate partial charging, and normally include a battery management system (BMS) that can report the state of charge, temperatures and alarms. Lead-acid batteries are usually discharged only partly to protect their life; LFP modules are typically specified for deeper discharge and more cycles. Ask the factory to state the depth of discharge, the cycle life and the warranty conditions in writing for the exact model, rather than relying on the brochure.

Voltage: match the 48 V system

An LFP module of 16 cells in series has a nominal voltage of 51.2 V; our 48 V module, for example, works between 44.8 and 57.6 V — its protection range, not a charging target. Telecom DC equipment is specified for a nominal −48 V with the positive pole earthed and a normal service range of −40.5 to −57.0 V (ETSI EN 300 132-2), so set the rectifiers' float voltage, and any boost, within the factory's recommended values and below your load's upper limit, and agree where to set the low-voltage disconnect.

Lithium modules usually need no equalising charge or temperature-compensated float: ask the factory which lead-acid functions of your rectifiers to switch off, whether the module suits a positive-earthed system, and which rectifier and power-system brands it has been tested with — with a communication link or on voltage alone. Do not mix lithium modules and lead-acid strings on the same bus unless the factory confirms it.

Communication and monitoring

Most modules talk to the power system over RS485 or CAN and give alarms through dry contacts. Ask for the protocol documentation, for what the BMS reports — state of charge, cell voltages and temperatures, alarm history — and for how a site will be monitored remotely. If your network management system needs SNMP, check whether your power system's controller provides it or a gateway is needed, and who supplies it.

Sizing and parallel modules

Runtime is usable energy divided by load. For example, a 4 kW load for 4 hours needs 16 kWh of usable energy; at 90% depth of discharge that is about 17.8 kWh of nominal capacity, so four 5.12 kWh modules (20.5 kWh) cover it when new with a margin of about 15%. That margin covers only about 13% of capacity loss: if you need the full runtime at the end of the warranted life — often stated as 70–80% of rated capacity — size for that figure and allow for DC losses and low temperatures. Check the maximum number of modules the factory allows in parallel and the continuous current per module, and size the cabling and breakers for it.

Temperature and the site

Lithium cells must not be charged below the minimum temperature the manufacturer specifies — usually around 0°C — and high temperatures shorten their life. Ask for the charge and discharge temperature ranges separately, and for a version with self-heating if your sites get frost. For outdoor cabinets, check the cabinet's cooling and the module's protection rating.

Where batteries at remote sites are at risk of theft, ask the factory which anti-theft functions the model has — for example a lock that disables a module removed from its site — and how they are activated.

Certificates and safety

Ask for test reports and certificates for the exact model: IEC 62619, the safety standard for lithium cells and batteries in industrial applications; UL 1973, the standard for stationary batteries that customers and inspectors in the United States and Canada commonly ask for; and the UN 38.3 test summary, which carriers and forwarders ask for. Operators often run their own acceptance tests — ask your customer which documents and tests it requires before you choose the factory.

Shipping

LFP modules are dangerous goods of class 9 — UN 3480 when shipped on their own, UN 3481 when packed with or contained in equipment; larger orders usually go by sea. By air, lithium-ion batteries shipped on their own are forbidden on passenger aircraft, travel with a Cargo Aircraft Only label and at no more than 30% state of charge unless the authorities approve otherwise, and, for batteries over 100 Wh, are limited to 35 kg per package — many rack modules weigh more, so ask the factory for the module weight and the packed weight. Ask how the factory packs and labels the modules and at what charge level it ships them, and check the first batch before the balance payment.

How we help

We match the module to your rectifiers and sites, ask the factory to confirm the voltage settings, the communication protocol and the temperature range in writing, collect the certificates and test reports for the exact model, and prepare the shipping and export documents. We work with orders from US$3,000.

← All articles

Send a request

* — required fields